Virtual Learning
K72
Threaded Assemblies: Essential Design Rules
Objectives:
Upon completion of the training course, attendees will be able to:
- Use appropriate practical rules to design threaded connections
- Design or improve threaded connections according to industry standards (NF E 25-030, etc.).
Date:
10th – 14th October 2022 (Mon-Fri)
Time:
14:30 – 18:00 (GMT+8) Singapore / 08:30 – 12:00 (GMT+1) Paris
Pre-requisites
Knowledge in mechanical design
Educational Approach
Technical presentations including theory, exercises, demonstrations, practical examples; punctuated with discussion and questioning from attendees.
Who should attend:
Engineers and design office and process planning technicians
Course outline:
- Morphology of screws and threaded studs
- Threads dimensions
- Mechanical properties of screws and threaded studs
- Stainless steel fasteners
- Nuts and threaded parts
- Designation of fasteners
Dynamic properties of fasteners
- Endurance limit of standardized fasteners
Analysis of an assembly
- Assembly modelling
- Analytical model and behavior
- Flexibility of assembly components
- Assembly behavior
- Complex assembly, pre-load, external loads and off-center loading
- Functional pre-load
Torque tightening of threaded assemblies
- Introduction to torque tightening and Torque – Tension relationship
- Friction coefficient characterization
- Notions of torque dispersion and tightening domain
- Process dispersion and tightening strategy
- Tightening stress
Assembly design
- Topic summary and standardization
- Simplified procedure for common assembly
- Complete procedure for structural assembly
Practical design rules
- Design of fastened parts
- Design of assembly function, corrosion and untightening
Trainer
This course will be conducted by Mr. Zouhair CHAIB, a trainer on bolted assembly.
Mr. Zouhair CHAIB
- Development of practices rules to design and to optimize bolted assemblies
- Expertise and analysis of failed connections
- R&D project treating of bolted connections
- Training activities
Areas of Expertise
- Design and optimization of bolted connections
- Analytical, FEA and experimental analysis of bolted joint
- Diagnostic and analysis of failed joints
- R&D and Training activities
- Software development
Profile
Career
CETIM, 2007 to 2013, and from July 2017: Technical referent in bolted joint
Nord-Lock, 2013 – 2017: Senior Technical expert in bolted joint
Labinal Snecma Group, 2001-2002: Calculation Engineer
Academic
INSA Toulouse, 2003-2007: Doctor Grade
ENIT Tunisie, to 2001: Mechanical Engineer
VIRTUAL LEARNING REGISTRATION FORM
Course Name
Course Date:
10th – 14th October 2022 (Mon-Fri)
Time:
14:30 – 18:00 (GMT+8) Singapore / 08:30 – 12:00 (GMT+1) Paris
Each day 3.5 hours for 5 days, total 17.5 hours
Closing Date:
27th September 2022, Tuesday.
Registrations will be confirmed in writing and is subject to availability
Course Fee:
SGD 1,7500.00 OR EUR 1,060.00 OR USD 1,300.00 per person (exclude GST)
Early Bird:
Registration must reach us on or before 13th September 2022, Tuesday:
SGD 1,575.00 OR EUR 960.00 OR USD 1,170.00 per person (exclude GST)
We welcome groups to attend our trainings. Please contact us for a group discount package.
Our Accounts will advise if GST is applicable. Participants shall bear all bank charges.
Learners must fulfill at least 75% attendance and pass all assessment components, to be awarded with a Certificate of Attendance (COA).
For clarification or inquiries please contact Ms. Pei Shyan NG or Joshua Lee at +65 67788285 or send an email to training@cetim-matcor.com
Registration Form
To register for the course, please complete this form.
Payment Details:
- Registration form and course fees are to reach MATCOR before the closing date.
- Registration will only be confirmed upon full payment.
- Direct internet banking payment to MATCOR Technology & Services Pte Ltd, Bank: Development Bank of Singapore, Bank Code: 7171, Branch Code: 032, Swift Code: DBSSSGSG, Bank Address: 1 Kim Seng Promenade, #02-32, Great World City, Singapore 237994, Account / Iban No: 032-004152-3. / PAYNOW: UEN199201190R
- All cheques should be made payable to “MATCOR Technology & Services Pte Ltd” and mailed to 3 Seletar Aerospace Link Singapore 797550, Or
- Overseas participants may choose to pay in EUR or USD.
- Participants shall bear all bank charges for payments.
For clarification or inquiries please contact Ms. Pei Shyan NG or Joshua Lee at +65 67788285 or send an email to training@cetim-matcor.com
Cancellation & Refund:
- Any cancellation made after closing date – no refund, but delegate substitution is allowed.
- Any cancellation made before closing date will receive full refund.
- MATCOR reserves the right to cancel or reschedule the course, only if deemed necessary
