Classroom Training

W-L67

Tight Bolted Joints using EN 1591 Design Method

Design bolted flange joints according to the tightness level requirement by applying the theoretical and practical (case studies) knowledge of the European calculation standard series EN 1591

Objectives:

Upon completion of the training, participants will be able to:

  • Explain the gasket parameters measurements as specified in EN 13555,
  • Understand and apply the calculations developed in EN 1591,
  • Design bolted flange joints in accordance with EN 1591

Date:

15 October 2024 – 17 October 2024

Time:

15:30 – 18:30 (GMT+8) Singapore /
08:30 – 11:30 (GMT+1) France

Pre-requisites:

Mechanical engineering background.

Pedagogical means:

Alternating theory and practise through exercises and case studies using dedicated software. Please bring along a scientific calculator.

Who should attend:

Engineers working in the field of pressure vessel and piping design, gaskets manufacturers, plant operators and maintenance.

Course Outline:

  • EN 1591-1 Design Method and Associated Standards Presentation
    • Introduction to EN 1591-1
    • EN 1591-1 Design Method
      • Hypothesis and principle
      • Consideration for different bolted joint components such as flange, bolts and gaskets
      • Consideration for different loadings such as pressure, differential thermal expansions, external loads etc.
      • Calculation Algorithm
      • Design to meet tightness requirements such as gasket effective surface and initial required tightening force for the bolt and tightening range definition regarding the tightening tool dispersion
      • Mechanical integrity checks for the bolted flange joints and Load ratio calculation
      • Comparison of EN 1591-1 versus Taylor Forge
  • CAP1591 CETIM Software
    • Case studies using CAP 1591 Software
  • Introduction to the Gaskets Parameters used in EN 1591-1
    • EN 13555: Test procedure for EN 1591-1 gasket parameters determination
    • EN 1591-2: Tabulated values of generic gasket data
    • Other sources of gaskets data
  • Application and Case Studies using CAP1591 CETIM Software

Trainer:

This course will be conducted by Mr. Stéphane JAVANAUD, engineer specialising in the field and providing consultancy services and technical assistance to businesses.

Mr. Stéphane JAVANAUD

Graduated from Ecole Nationale Supérieur d’Ingénieurs de Bretagne Sud (ENSIBS), France 2016 Experience in the field of bolted flange joints, elastomeric seals and Finite Element Analysis.

Areas of Expertises

Engineer in the sealing technologies Cetim’s Lab since 2016.

Gasket testing: definition of test procedures for gasket characterization and qualification for gasket manufacturers and end-users in the field of Oil & Gas, Nuclear and chemical industry

Bolted flange connection calculation:

Training for industry on bolted flange joints and EN1591 calculation method

Publications

Materials and Design volume 156 (2018): Temperature-dependent modelling of a HNBR O-ring seal above and below the glass transition temperature. (https://doi.org/10.1016/j.matdes.2018.06.016).

ASME PVP 2018: Flange Gasket Behavior Characterization for Service in Arctic Environment (PVP2018-84284).

Profile

Graduated from Ecole Nationale Supérieur d’Ingénieurs de Bretagne Sud (ENSIBS), France 2016

Experience in the field of bolted flange joints, elastomeric seals and Finite Element Analysis.

Course Name:

W-L67: Tight Bolted Joints using EN 1591 Design Method

Course Date:

15 October 2024 – 17 October 2024

Time:

15:30 – 18:30 (GMT+8) Singapore /
08:30 – 11:30 (GMT+1) France

Closing Date:

1 October 2024, Tuesday

Course Fee:

SGD 900.00 per person (exclude GST)

We welcome groups to attend our trainings. Please contact us for a group discount package.

Our Accounts will advise if GST is applicable. Participants shall bear all bank charges.

Learners must fulfill at least 75% attendance and pass all assessment components, to be awarded with a Certificate of Attendance (COA).

For clarification or inquiries please contact Mrs Lorraine HUANG at +65 67788285 or send an email to training@cetim-matcor.com

Registration Form

To register for the course, please complete this form.

Payment Details:

  • Registration form and course fees are to reach MATCOR before the closing date.
  • Registration will only be confirmed upon full payment.
  • Direct internet banking payment to MATCOR Technology & Services Pte Ltd, Bank: Development Bank of Singapore, Bank Code: 7171, Branch Code: 032, Swift Code: DBSSSGSG, Bank Address: 1 Kim Seng Promenade, #02-32, Great World City, Singapore 237994, Account / Iban No: 032-004152-3. / PAYNOW: UEN199201190R
  • All cheques should be made payable to “MATCOR Technology & Services Pte Ltd” and mailed to 3 Seletar Aerospace Link Singapore 797550, Or
  • Overseas participants may choose to pay in EUR or USD.
  • Participants shall bear all bank charges for payments.

For clarification or inquiries please contact Mrs Lorraine HUANG  at +65 67788285 or send an email to training@cetim-matcor.com

Cancellation & Refund:

  • Any cancellation made after closing date – no refund, but delegate substitution is allowed.
  • Any cancellation made before closing date will receive full refund.
  • MATCOR reserves the right to cancel or reschedule the course, only if deemed necessary